by: Andras [ ]
Originally published on:
As an introduction I have to admit that I love models featuring their interior. If I can, I buy aftermarket sets to enhance my models, and obviously I was overjoyed by the recent influx of tanks with full interior by several manufacturers. Modelcollect has been on my radar for a long time now, because I do like to build post-war Soviet armor/trucks, and I also like that the 1/72 scale Modelcollect kits usually come with PE and metal barrels, which is really unusual -and amazing-, and more importantly, I like their prices. When I saw that they were working on a series of tanks with interior included, obviously I became very much interested indeed. I kept checking their online shop to see when these tanks become available, and when the E-50 and E-75 finally did, I immediately went and purchased the E-75.
The first thing I received was a sprue of the top of the hull. That was all I got in the cardboard box, and there was no explanation included. This made me worried for a while as you can imagine, but it took me just an email to clear up the situation: Modelcollect sent out replacement sprues for all the E-75 they sold. Exceptional customer service Iíd say. (The reason, as far as I could determine, was that the top hull was somewhat damaged in the original sprue - the back of the engine compartment is a thin plastic strip, and it was bent a little in my sample. Other than that I could not find any differences between the original and the replacement.)
The tank itself is a paper panzer: it never got further than the planning phase. It was planned to use a lot of the Tiger II components, and looks remarkably similar to it. I suspect the modelís interior was designed using the Tiger II as a template - after all German tank designs were quite conservative during the war, so it is a safe bet from Modelcollect. The model is packed in a somewhat thin cardboard box; the box art is a technical drawing of the tank against a black background.
The kit comes with several extra parts you will not use during the building phase; an extra lower turret, two E-50 turrets, and a lot of smaller bits. (This seems to be the case with most Modelcollect kits; my spares box has been filling up lately from the leftovers of the three models Iíve bought.) The introduction on the instructions are taken from the wikipedia page of the E-50. (A mistake obviously.)
The instructions are provided as a foldout on high quality, glossy paper. The steps are outlined well and look clear, but during the building phase I ran into a couple of issues, which I will highlight over the course of the review. None of these issues are deal-breaking, but they did cause me some headache; however if you know about them you will have no problems whatsoever during the build. (I guess this is one of the reasons to read reviews.)
The model also comes with a very large set of PE: apart from interior details and a lot (and I mean a lot) of round disks for the bottom of the ammunition, we also get the back and front mudguards as optional PE parts, and the track guards are included as well. A lot of the PE is not used for the build; Iím honestly not sure what they are for. Itís an intriguing enigma. There is also a small fret for the engine deck grilles, periscope covers and lifting hooks. A third tiny PE fret is also included, which is not used at all. (And not included in the sprue layout section of the instructions, either.) Another mystery; if anyone has the answers, please let me know in the forum. Thereís a nice-looking crew included if you want to place them inside the tank; the detail is not as fine as some resin offeringsí, but they are still pretty good. The plastic is somewhat fragile. The parts are finely cast, but there is some flash (not a lot), and the detail is OK, but not exceptional.
The interior is not too detailed, unfortunately. I know Iím asking for a lot here, so take this criticism with a grain of salt. The basics are in, but there is a lot more that could have been done. The detail from the firewall is missing completely, and the radio-operatorís station has no detail at all. The seats have no moulded-on detail of padding, and the turret is missing a lot of things (fume extractor, electrical boxes, etc.). Obviously this is a 1/72 scale kit, so the expectations need to be adjusted a bit, but I still would have liked to see a more comprehensive interior. If you plan to build the tank with only the hatches open most of it will be invisible, so it may not be an issue for you -but then why not buy the cheaper version with no interior? I built the model as a cutaway, so for me the more detail the model has, the better. My impression is that originally the tank was not planned with an interior, but it was added to it later. The interior sides of the larger parts (hull, turret, etc.) have no markings where the different interior detail should go, and some hatches are moulded shut. A lot of the PE options look like an afterthought, too, and sometimes surgery is necessary before installing them (Iím thinking of the front and back mudguards mostly).
The first step details the addition of extra track links to the turret; I would leave them off until after the painting is done. The teeth are supposed to be replaced using PE replacements; Iíve left them as they were. (The instructions are not clear about removing the plastic teeth, and they are tiny anyway.)
The second step assembles the turret basket (very nice PE plate), and the third finishes off most of the turret interior and the gun. This is where you run into the first issue: the metal barrel should fit onto a small peg on part A6- but there is no hole drilled into the metal. I cut the peg off and tried to glue the barrel to the plastic base as straight as I could; itís still a bit wonky if Iím honest. Only after painting -when I was putting the leftover bits into the spares box- did I realize that we actually get a proper mantlet that can fit the metal barrel (A9 instead of A8). This is a recurring problem with the instructions- they seem to have been designed for an all-plastic model, which was modified later to include PE, metal barrel and interior. Unfortunately not all the modifications made their way into the instructions; some did, but this particular one, for example, apparently did not. Regardless now you know, so you can use the correct part.
There are two turret bases included, but the instruction does not give the part number, so I have no idea if I used the right one. This is again a tricky issue. The turret ring on the hull does not have the holes for the interlocking pegs normally moulded onto the ring of the turret itself. These are very well known features of almost all tank models: this is how the turret is locked into place. Upon inspection you will find that one of the turret bases has these little pegs, while the other does not. The latter one would go better with this model, but at the end of the day it makes little difference which one you choose to use. Obviously I used the ones that had them as I did not notice these differences during the building phaseÖ
The turret bottom has moulded-on holders for the gun; these are unnecessary, since the gun comes with its own support-and these details are not featured in the instructions, either. (You just have to cut them off.) Where the gun goes exactly is not marked anywhere, unfortunately; I used the location of the holding pegs I cut away to attach the gun.
Step 4 finishes off the turret exterior: hatches, lifting hooks and everything else. Unfortunately the back access hatch cannot be displayed opened; and the loaderís hatch can only be opened about 90 degrees, because the fume extractor housing is in the way.
Step 5 and 6 work on the upper hull and engine deck: you have an option to cut off the moulded-on mudguard, and substitute it with a PE one (tiny PE part alert). There are also PE guards supplied for the whole length of the tank; this is really nice if you want to show them damaged, bent or missing. I would not add them to the hull at this stage, though -wait until you finished the hull and running gear. (There are no markings where exactly should the tools, towing cables, trackguards go.) The engine deck has nice PE grilles.
None of the engine access hatches or the driverís/radio operatorís hatches can be opened; this is a shame, since you do get an engine compartment and a driverís compartment. Unless you are building a cutaway these details will be invisible once you finish the build.
Steps 7-10 detail the assembly of the running gear/tracks. The process is quite easy and straightforward. The E series was not planned to use torsion bars; the special spring suspension is nicely replicated. The positions of swing arms, however, are not very obvious. You can move them up or down, hence adjust the road wheels to any terrain, but the ďneutralĒ setting is not very clear.
The kit comes with link-and-length tracks, which is a very good option for this scale. The links are left and right handed; something the instructions do not say or indicate. You should sort the track links first and then start with the assembly. I cut off the connecting pins from them because it was easier to assemble them (they are a bit clunky and donít fit very well into their grooves). The number of links necessary for the tracks shown on figure 10 is not correct; you will need at least five extra individual links to finish the complete track.
Step 11-12 shows the assembly of the engine compartment. There is some flash on the lower hull which needs to be removed. The basic layout is created by parts H18 and H4; there are no guiding grooves within the lower hull to help you with the placement. (Itís not difficult to find the correct position, but it would still be nice to have them. The engine is quite detailed little thing, and once finished the whole engine compartment looks pretty good. Some larger pipes can be scratchbuilt if you are so inclined; overall, itís a really good representation of the real thing in this scale. The problem is that none of it will be visible if you close the engine deck, since the access hatches cannot be displayed open.
Step 13-15 details the assembly of the interior. It is somewhat basic, but generally enough in this scale. The radio operatorís station in quite neglected as I mentioned; if you plan to do a cutaway, best use the driverís side, or work on your scratchbuilding skills. To make painting easier do not yet glue the bottom of the fighting compartment into the hull; I did, and it made painting somewhat difficult.
Step 16 shows the assembly of the ammo racks; depending on how you want to display the tank you may not need to bother with all the PE disks for the ammunition. The place where part J8 should be placed is not marked on the hull.
Step 17-19 show the assembly of the back armor plate of the tank. The detail is pretty good, but Iím not sure the suggested sequence is correct. You have an option of using a PE mudguard; for this you need to remove the moulded-on plastic part. The instructions would have you attach all the small parts to the panel and then remove the plastic mudguards. Performing this surgery first, and then adding the protruding details might be a better way of doing it. I would also glue the panel to the hull before adding the smaller bits; the fit is tight, and it takes some fiddling to slot it in place. (I generally prefer finishing off the large assemblies first, and then add the details to minimize damage later on; this means Iíve installed this part when I was finished with the tub of the hull and before I installed the interior.)
Step 20 is the final assembly. The top of the hull does not fit perfectly to the bottom which necessitated some sanding on the sides of the lower hull to achieve a good fit. As mentioned at step 1, the turret ring on the hull is perfectly circular; there are no notches that would allow the turret to lock onto the hull. This may be annoying to some, but I think itís actually a good thing: it allows you to display the tank with the turret off, without having to make those notches disappear. It also means that nothing keeps the turret in place if you donít glue or magnetize it.
Once the assembly was done Iíve chosen a hypothetical (and funky looking) camo pattern; I did not like the plain dunkelgelb suggested by the assembly.
Overall the detail is good, the subject is great (depending on your preferences, of course), and the interior is a very welcome bonus. What really lets the model down is the instructions; as I pointed it out several times they are not very good at certain steps, and at others they are flat out wrong. This is not a deal-breaker; especially if are aware of the weak areas. The model, as I mentioned, was improved from an all-plastic version. The design of the ďbaseĒ pieces, the several extra parts, and the somewhat mangled instructions all seem to point to this direction. There is nothing wrong with improving existing models; I just wish the instructions were improved to the same level as the model itself was. It is certainly not a bad model by any measures I have to add; in fact I quite like it, and Iím really looking forward to building the T-80 I have in my stash -and the T-72 with interior still to be issued.
To sum up: what can you use this model for? As I mentioned it a couple of times already, if you just build it out of the box, most of the interior detail will not be visible. In this case you are better off ordering the non-interior version. (This is a very good idea MiniArt seems to be adopting, too: a budget version for most people, and a ďpremiumĒ version with interior for the more unhallowed model builders.)
The interior version is a very good option if you plan to build a damaged tank, or a tank under repair. For these purposes this model offers an incredible deal, since it is relatively inexpensive, and has enough detail to showcase it with the turret lifted off with a crane. If you want to add more detail, you can use the Tiger II as a guide and either scratchbuild the missing detail, or adopt one of the aftermarket resin interior sets available for the Tiger I. I think Modelcollect could have gone a bit further with detail even if it means an increase of price: after all, there is a cheaper alternative available, and this was always going to be a niche product, so why not go all the way? Regardless if would like to build something special; this is definitely a good model to grab.